Close

Armasight Scope Mounting System #3 for Clip-On Day/Night System

This product is no longer available, please consider this similar product instead

Armasight Scope Mounting System #3 for Clip-On Day/Night System ANAM000011

Model no: ANAM000011

Share with friends


  • Fits scopes with 42-50mm diameter.

  • Works with Armasight Apollo Thermal Clipons and other Armsight NV devices

Armasight Scope Mounting System #3 for Clip-On Day/Night System Description



Armasight Scope Mounting System #3 attaches the Armasight Clip-On Day/Night System directly onto the front bell of any day-time scope with objective diameters between 42 mm and 50 mm. Examples: 42 mm - Leupold Mark 4 2.5-8x36, Kahles 4x36; 46.7 mm - Leupold 3.5-10x40, Leupold VX-II 3-9x40; 48 mm - Zeiss 1.5-6x42, Swarovski PV-N 2.5-10x42; 48.7-49 mm - Meopta Artemis 3000 3-9x42; 49.5 mm - Meopta Artemis 3000 4-12x40; 50 mm - Schmidt & Bender 10x42

Technical Specifications

Made in Ukraine

Ask a question (5)

Questions on Armasight Scope Mounting System #3 for Clip-On Day/Night System

Sort by Descending
  • From Gerald at 2/12/15 4:00 PM

    • Q: On your armasight thermal clip on adapters, do you have inserts for scopes with a smaller objective diameter than 42mm?

    • A: Hi Gerald, can you describe your full setup? Is the thermal scope going to be mounted directly onto the dayscope? Is there room on the rail to mount the scope directly to the rail? What is the daytime optic you will be using? We can certainly make suggestions for the correct setup once we have this information.

    • Do you find this question helpful?  Yes   No
  • From Sidney at 1/26/16 1:08 PM

    • Q: The scope had just enough room underneath it to squeeze this adapter on. If the adapter fits good, but is barely touching the barrel is it safe to fire?

    • A: Hi Sidney. Sorry for the delay in response. What you described should not be a problem if all the part are connected well.

    • Do you find this question helpful?  Yes   No
  • From Paul at 6/3/16 11:44 PM

    • Q: Two questions.

      1. If I buy the one to fit a 50 mm objective can I buy just the insert to fit on a 40 mm objective?
      2. I need this mounting system so that the unit can be used on my SBR. Not enough rail. My SBR has a 10.5" barrel and I have a Vortex 4-16 PST on it. I only shoot it with my AAC 7.62 SDN on it. Any concern that the unit will get damaged if partly over a suppressor? Lense etching, etc.

    • A: Hi Paul. We need to do a bit of research for you. Please give us a day or so to come back with the answers.

    • Do you find this question helpful?  Yes   No
  • From Dave at 6/8/17 8:27 AM

    • Q: Hello, I am getting ready to pull the trigger on one of these for my co-mr 3p. I would just like to know if the dimensions listed are the outside objective bell diameter. So for example my objective lens is 32mm and the objective bell outside diameter is 38 mm, so would the adapter #2 be my best bet. This will be used on my cz452.

    • A: Hi Dave.

      Adapter #2 is the correct adapter for your scope.

    • Do you find this question helpful?  Yes   No
  • From David at 1/11/18 4:33 PM

    • Q: If I use this adaptor to mount my clip on to my normal day scope I do not have to have the clip on attached to a rail correct? The adaptor will hold the weight of the clip on to the day scope?

    • A: Hi David.

      That is correct. If you attach to the rail, then this adapter is not needed. This adapter allows you to couple the clipon to the scope.

    • Do you find this question helpful?  Yes   No

Close
Sign up for instant coupon code!

Sign up for our newsletter

Open Newsletter Popup
Close